Makes sure to go all the way around the pipe - leave no gaps in the glue. Once the primer is dry, apply the PVC glue to the end of the flexible PVC pipe. Prepare the outside ends of the flexible PVC pipe with a light coating of PVC primer.Īfter a few seconds, the primer will dry. Prepare the insides of the male pipe adaptors with a light coating of the PVC primer. Your kit will include both Red Hot PVC primer and PVC glue. The silicone on the threads will prevent any possible leaking. Once you've tightened the fittings as much as you can with just your hand - that's enough. You only need to "hand-tighten" these male pipe adaptors - no need to use a large wrench. The inlet is located above the drain port and off to the side of the filter. The drain port is located at the middle and bottom of the settling cone. Hand tighten the siliconed male pipe adaptors into both the brass inlet port and the drain port of the Hydro Vortex™ filter. A plug comes with the larger filters to plug the unused inlet.) (The Ahi Hydro Vortex™ filter has one inlet and one drain - the Marlin and Dolphin filters have two inlets and a drain. The first step is to place a bead of silicone around the threads of both the inlet and drain pipe adaptors. Your Hydro Vortex™ filter comes complete with all fittings and a tube of silicone sealant. Once the ground under the filter is firm and level you're ready to proceed with hooking up it's plumbing lines. The first step is to create a level and firm are for the Hydro Vortex™ filter. For this particular pondless waterfall - we're using an Ahi Series pondless waterfall with 20' stream kit with the HydroFlush™ self cleaning backwash system. With your pondless waterfall kit on site - you're ready to start. If we don't have a stock kit in your size, we'll happily create a custom kit for you - just give us a call or an email. These measurements will tell you what size pondless waterfall kit you'll need. With the pondless drawing in “actual” size now, measure the length and width of your design from one end to the other. Then simply paint the stream between the Hydro Vortex™ waterfall filter and the HydroSieve™. Then at the other end of your pondless waterfall design, paint where the HydroSieve™ and the HydroChamber™ will be installed. Using your pondless drawing as your guide, first paint where the Hydro Vortex™ waterfall filter will be installed. Having it painted on the ground gives you a much better idea of what you are creating. The next step is to paint your pondless design on the ground in actual size. Once you’re fairly satisfied with the pondless waterfall drawing, it’s time for the next step. You’ll be able to make as many changes to your pondless waterfall drawing as you wish – make it longer, shorter, have more curves, less curves – you’re in charge. If you need help, simply give us a call – we’re here to help you. The first step in learning how to build a pondless waterfall is to create a drawing of the pondless water feature you are envisioning. The system is “pondless” because when the pump is turned off – all the water is captured and stored out of sight inside the HydroChamber™.Ĭleaning the ULTIMATE Pondless Waterfall is easy – simply empty the leaves and debris from the HydroSieve™ pre-filter, and backwash the Hydro Vortex™ waterfall filter with your choice of backwash options: Manual, or with the HydroFlush™ self-cleaning backwash system. The system also utilizes a tank for the water storage instead of the impossible to clean rock and gravel reservoir basins that other pondless systems feature. The ULTIMATE Pondless Waterfall is both pre-filtered, and biologically filtered. The ULTIMATE Pondless Waterfall is the only completely filtered pondless waterfall system. How to Build a Pondless Waterfall with a Stream Get a Custom Ultimate Pondless Waterfall Kit Quote
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |